our Cone crusher is suitable for crushing varies of mid-hard and above mid-hard ores and rocks. It has the advantage of reliable construction, high prod activity, easy adjustment and less cost in operation. The spring release system of cone crusher acts an overload protection system that allows tramp to pass through the crushing chamber without damage to the crusher, use dry oil, water, two kinds of sealed formation. It makes plaster stone and engine oil separated, assured reliable performance.
Cone Crusher Features:
1) High productivity and quality
2) Reduce off time
3) Easy maintenance, low cost
4) Provide unparalleled crushing in medium and fine crush
Cone Crusher Working Principle
How Cone Crusher works
During operation, the motor of Cone Crusher Crushes drives the eccentric shaft shell to turn around through ahorizontal axle and a pair of bevel gear. The axle of crushing cone swings with the force of eccentric shaft shell so that the surface of the crushing wall is close to the roll mortar wall from time to time. In this way, the ores and rocks will be pressed and crooked and crushed.
Installation of Cone Crusher thrust bearing
To ensure the precision of thrust bearing installation in cone crusher, installation must be the following steps:
(1) the installation of the thrust bearing should be same to steps of scratching.
(2) first, jaw plate placed in a case back should be smooth,if case back has the burr and the remaining sand,please clean up.Then pour lubricating oil to just the top of jaw plate.
(3) then install the middle circle plate and circle plate
(4) Finally, install the air eccentric shaft, spherical tile racks, and spindle. When installing air eccentric shaft,the big gear weight should be placed in the top of small gear,so that the outer end of bevel gear is alignment.After spherical waham installed, the gap between spherical bearing seat and the main machine is as big as possible.During installation, measure the three data: a. gap of cone gear; b. gap between principal axis and spindle sleeve; c. gap between empty eccentric shaft and spherical waham.
Cone crusher specification:
| Type | Outside diameter Of crushing cone (mm) | Max feed size (mm) | The adjusting range of discharger (mm) | Crushing capacity (t/h) | Electric motor power (kw) | Speed of Eccentric shaft (r/min) | weight (T) | |
| PYB | 600 | 600 | 65 | 12-15 | 40 | 30 | 356 | 5 |
| PYD | 35 | 3-13 | 12-23 | 5.1 | ||||
| PYB | 900 | 900 | 115 | 15-50 | 50-90 | 55 | 333 | 11.2 |
| PYZ | 60 | 5-20 | 20-65 | 11.2 | ||||
| PYD | 40 | 3-13 | 15-50 | 11.3 | ||||
| PYB | 1200 | 1200 | 145 | 20-50 | 110-168 | 110 | 300 | 24.7 |
| PYZ | 100 | 8-25 | 42-135 | 25 | ||||
| PYD | 50 | 3-15 | 18-105 | 25.3 | ||||
| PYB | 1750 | 1750 | 215 | 25-50 | 280-480 | 160 | 245 | 50.3 |
| PYZ | 185 | 10-30 | 115-320 | 50.3 | ||||
| PYD | 85 | 5-15 | 75-230 | 50.2 | ||||
| PYB | 2200 | 2200 | 300 | 30-60 | 59-1000 | 280-260 | 220 | 80 |
| PYZ | 230 | 10-30 | 200-580 | 80 | ||||
| PYD | 100 | 5-15 | 120-340 | 81.4 | ||||
Note: If there is change of the above specification, it subjects to the newest products' specifications.